fixed : upgrade broken HD in old Time Capsule

Question :

My 1st generation Time Capsule always used to work fine, but now the internal HardDisk is broken.

Can I replace the HardDisk easily ?

 

Answer :

Yes you can.

In the ‘old’ flat Time Capsule (like the A1254 “1st generation” Time Capsule), the HardDrive is rather easy to replace. And even though Apple has marked this TimeCapsule ‘obsolete’ it is still able to preform properly and it can be maintained using the current AirPort Utility version 6 and newer.

To do so, follow these steps :

  • get yourself a new HardDisk, preferably a low-energy HD like the Western Digital WD Green 2TB or 3TB (get it on Amazon.com, Amazon.co.uk or Amazon.de) ; these low-energy HDs are especially suited not only because of their low power consumption, but also because of their ability to stay cool during operation since these old TimeCapsules tend to overheat when a regular HD is installed
  • then, place the TimeCapsule upside-down and warm up the rubber bottom plate with a hairdryer to loosen the glue (if you don’t do this, it is nearly impossible to get the rubber bottom plate of without rupturing it)
  • then follow the steps as outlined in this manual by iFixit and be sure to read the important note at Step 2 : “The two screws in the top center of this picture should not be removed at this time. They are locating pins on the hard drive.”
  • then replace the HD and rebuild your TimeCapsule doing the MacFixit steps in revers direction
  • when done, plug your Time Capsule into the power and access it using the AirPort Utility app on your Mac (or iPhone/iPad)
  • in the AirPort Utility app, select the TimeCapsule’s icon and click Edit
  • in the window that opens, go to Disks, then click Erase Disk
  • when that’s done, your new Time Capsule’s HD is ready for use

That’s it 😉

enjoy !

Advertisements

fixed : use internal SATA hard drive in LaCie “Mac mini”-form factor housing

Question :

I have an old, square-ish Mac mini (2005 through June 2010), which back-ups to a LaCie FireWire 400 harddrive with the same square-ish form-factor. This morning however, the harddrive inside the LaCie mini has died…

I could just get a completely new external hard drive (with a different design) for my backups now, but I really like the square-ish housing of the LaCie mini together with the Mac mini, so I’ve decided to replace the internal hard disk.

However, it turns out that the internal hard disk of the LaCie mini is an IDE (ATA) hard disk, which are increasingly harder to get than the current Serial-ATA (SATA) hard disks, and generally even more expensive.

Is there a way to use an internal SATA hard disk inside the LaCie mini housing ?

Answer :

Yes, there is.

What you need is this :

– a high-capacity internal 2.5″ laptop SATA harddisk (it is possible using a 3.5″ desktop SATA harddisk, but that is not recommended as explained at the bottom of this post), like a Hitachi TravelStar 1TB SATA harddisk

– a 2.5″ to 3.5″ bay converter-frame, or preferably just the Digitus 2.5″ to 3.5″ bay converter-brackets or alike

– a Wintech SAK-65 bi-directional SATA-to-IDE converter (because of the limited space inside the LaCie mini housing, most other IDE-to-SATA converters will be too bulky too fit in one direction or another)

Note : the Wintech SAK-65 comes with all cables to connect a SATA hard disk to the LaCie mini IDE/ATA-internal

When you have all these parts, the build-in is rather straight forward, especially if you use the manual provided with the Wintech Converter. In short :

1- unplug the LaCie mini form the power and FireWire cables, then remove the white plastic triangular feet from the LaCie mini housing (the are sticker-type feet, so temporarily stick them to a clean smooth surface to store) and unscrew the  screws you find beneath them

2- gently open the housing, unscrew the broken iDE/ATA-hard drive, and take it out

3- gently disconnect the ATA-to-ATA cable, and take it out also

4- then put the new SATA-hard drive in and screw it into place

5- then connect the Wintech converter as outlined in the instruction manual (so, set it’s switch to “Device” and do not forget to connect it to the power using the provided Molex extension cable that includes an extra power connector for the Wintech connector)

6- then connect both Wentronic cables to the hard disk on one end and on the other end to the Molex cable and the Wintech connector

7- then make sure the Wintech connector is slightly twisted in such a way that it is a flat on the hard drive as possible and gently close up the housing (don’t forget the plastic feet)

8- reconnect the power and FireWire cables, and then the LaCie mini will be recognized as and ‘unreadable’ drive by your Mac mini

9- use OSX’s Disk Utility-app to format the drive to “Mac Journaled” format, and it will appear as a healthy drive on your Mac (ready for use, for Time Machine backups or alike)

That’s it

😉

—————————

If you really want to build a 3.5″ SATA harddisk into this LaCie mini housing, it can be done, but it will fit so extremely tight that it comes with some extra things you need to address :

1- you will NOT need the 2.5″ to 3.5″ converter brackets

2- the provided cables will not fit in such a way that the housing can be properly rebuilt, so you will also need :

– a Wentronic 4p-Molex-to-angled-15p-SATA power cable (none of the cables with a regular straight SATA-connector will fit, and even most of the angled SATA-connectors will be too bulky too fit, and even this one leaves less than a mm of room for the housing) to extend the “Molex-with-an-extra-power-wire-for-the-converter”-cable

– a Wentronic SATA-to-angled-SATA data cable (most of the other angled-SATA connectors will be too bulky, but the Belkin SATA-to-angled-SATA data cable will fit as well), but you will even have to strip a little extra off the angled connector to enable the cable to make a ‘near-360’-corner

3- the Wintech SAK-65 bi-directional SATA-to-IDE converter needs to be used stripped of it’s plastic housing as it’s too bulky, and you will need to extend the IDE Master/Slave-cable (the wide and flat cable that looks like a lot of tiny wires next to each other) by opening the connection on the converter and putting the original one from the LaCie mini housing in it’s place (after having taken off the connector of that one also)

4- make sure you don’t adjust the 3.5″ SATA harddrive using the screws, just put it ‘on the floor plate'(to make a little extra space)

5- …and then you will have to puzzle quite a bit to fit all of that into the housing

As mentioned before : using a 2.5″ SATA harddrive is far more convenient and straight forward !

Whichever solution you choose :

Enjoy !

😉

Donate Button (MacManusNL)