fixed : “Your iPad could not be activated”/”Activation server temporarily unavailable”-error

Question :

After my iPad tried to update to iOS 9.3.x (this also goes for iOS 11.2.x) last night, I had to re-enter my AppleID and now I’m getting a blank page with only this error message :

“Your iPad could not be activated because the activation server is temporarily unavailable. Try connecting your iPadto iTunes to activated it or try again in couple of minutes.”

But even if I wait a couple of minutes or even an hour, and try again, I get stuck with this same message…

How can I fix this ?

 

Answer :

Apple Support has a tutorial on how to fix this, but a lot of times that doesn’t work :

If you can’t activate your iPad 2 (GSM model) after you update to iOS 9.3

If you can’t figure out how to do that, or you’ve tried and it doesn’t work for you, try this :

  • if you have an iPad with a GSM SIM-card installed, make sure you have the SIM’s 4-digit PIN-code at hand, then pop the SIM-card out using a bended paperclip or the official tool that’s comes with every iPhone and every SIM-card enabled iPad
  • then, on your Mac, go to Apple-icon (top-left in the menu bar) –> system Preferences –> iCloud
  • in the window that opens, see what eMail-address is listed under your name ; make sure to remember that eMail-address : this is your iCloud-account name (which might be different from your AppleID or iTunes Store-account name)
  • then click on “Account Details” and type the password that is connected to your iCloud-account name
  • if a new window opens, remember this password and close the window
  • if you get an error message that your password is incorrect, make sure you find the password and try again (you can try several times, but if you get a warning that you have only a limited amount of attempts remaining, stop immediately !! and skip this step)
  • now return to your iPad and do a reset by pressing the Home-button (physical button below the screen) and the Power-button (physical button on the right edge or top edge) simultaneously until the screen goes black and the white Apple logo appears
  • now, proceed though the following screens as you normally would until you are asked to enter your Account Name : there you should enter the eMail-address that is your iCloud-account name and the corresponding password
  • if this works, don’t forget to put the Sim-card back into your iPad and you’re done
  • if you happen to run into the Activation Server error page again before you get to the page where you should enter your Account Name, do this :
    • open the AppStore-app on your Mac
    • make sure you have installed all official Apple updates (especially iTunes)
    • connect your iPad directly (so without USB-hubs) to your Mac using the iPad-to-USB-cable
    • on your Mac, open iTunes
    • then do the reset on you iPad agian, simultaneously pressing the Home- and Power-buttons until the Apple logo appears
    • now iTunes (on your Mac) should detect your iPad
    • if it doesn’t, try the reset again
    • if it does, see if you can go trough all setup screen on your iPad
    • if you are unable to do so, go to iTunes on your Mac
    • if a message appears you need to unlock your iPad, type the screen unlock code on your iPad
    • if a “Trust this iPad ?” message appears on your Mac, click “Trust”
    • if a “Trust this Mac ?” message appears on your iPad, click “Trust”
    • now you see a small button with an iPad on it next to the Music/Films/etc.-pulldown menu ; click on it
    • in the next window, you should now be able to initiate the iOS-update of your iPad from your computer
    • then wait for the update to complete
  • afterwards, do not forget to put the SIM-card back into your iPad

Good luck & enjoy 😉

Advertisements

fixed : get new iPhone’s photos on old Snow Leopard OSX10.6.8-Mac

UPDATE : the procedure outlined in this post still works for new iPhones with iOS11 and iOS12 (like the iPhone 7, 8, X, XS and XR) even though it was originally written for new iPhones running iOS10 (like the iPhone 6 and 6s)


Question :

I just got a new iPhone 7, and now I want to transfer my photos from my previous iPhone 6 onto my MacBook. I was hoping to use iCloud for this, but my MacBook is rather old and can’t run any version of OSX newer than MacOSX 10.6.8 “Snow Leopard” which doesn’t have iCloud installed, just it’s predecessor MobileMe…

What can I do ?

 

Answer :

Theoretically, you could also go online from your Mac and get access to your photos through the iCloud.com website… but since the latest versions of Safari, Chrome and Firefox don’t support MacOSX 10.6.8 any longer (Opera does for now, but that’s about to change also), this route is not a future-proof solution.

The most future-proof solution is using a USB-connection like this :

  • on your Mac, open the Applications-folder and open the Image Capture app
  • now connect your iPhone to your Mac using a USB-cable
  • you will get this error message [ Photos in the Camera Roll on “…” cannot be viewed or imported because the iPhone is locked with a passcode”
  • click on OK
  • then unlock your iPhone with your fingerprint (or type your 6-digit unlock code)
  • on the iPhone you will get this message [ Trust this computer? ]
  • click on Trust
  • then in Image Capture, under Devices, click on iPhone
  • now all the photos on your iPhone will be listed and/or displayed on your Mac
  • from the pulldown list at “Import to:” select a folder to import the photos to (the default folder is your Pictures-folder, but you can also choose iPhoto or create a new folder at “Other…”)
  • then select the individual photos you want to import and click on Import, or click on Import All to import all your iPhone’s photos onto your Mac
  • then wait…

that’s it – enjoy 😉

Donate Button (MacManusNL)

fixed : switching the language of the spelling check in iOS5, iOS6, iOS7, iOS8, iOS9, iOS10, iOS11 & iOS12

Question :

Is it possible to (quickly) switch the language of the spelling check while I’m writing a message on my iPhone ?

Answer :

Yes !

It’s really simple :

1- make sure you have installed multiple languages / multiple keyboards on your iPhone or iPad : Go to Settings –> General –> Keyboard –> (International) Keyboards –> Add New Keyboard…

…and select your desired languages from the list (then exit the Settings-app)

2- you have now installed not only the keyboard for each language, but also the spelling check… and it’s now available in any text or message you type (including SMS)

3- to switch the language of the spelling check, just tap on the globe-key next to the space-bar : when tap it, the space-bar will (only for a quick second) display the name of the keyboard you’re using… but… the language of the active keyboard layout is also the language of the active spelling check…

😉

Donate Button (all)